No China Parts or Labor.
Polar Air by Eaton Compressor uses NO China parts: Read More
Gardner Denver, US Electric Motor, Schneider, Mann and VMC.
Our Major brand parts suppliers that we use : Read More
Finish Built and Tested in the USA.
Our USA factory assembly line custom builds each compressor to the customer’s order and specifications. : Read More
100% Duty Cycle Ultra Quiet Design.
We guarantee 100% duty cycle up to 24/7 operation of the compressor.: Read More
Certification, UL/CSA listed and ASME/CRN Tank Certified.
Our compressors are UL and CSA listed.: Read More
Legendary Precision GD Twin Rotary Screw Oil Flooded Pump. Energy Saver.
Legendary Tamrotor by Gardner Denver pumps provide 24/7 operation: Read More
Legendary US Motor Corp: Nema Standard, TEFC, 12 lead Premium Efficiency Electric and Aegis grounding ring with insulated front and rear bearings. Energy Saver.
Low RPM of 1750 rpm provides high cold weather starting torque (not 3450 rpm) design. : Read More
Legendary Schneider Y/Delta Soft-Starting Magnetic Starter Switches. 12 Lead Energy Saver.
Saves up to 1/3rd in peak starting demand. : Read More
Smart Technology Programmable Controller Saves Energy.
Simplifies Compressor Functions: Read More In Depth Explanation
Polar air by Eaton Compressor has defined three goals intended to make us the most successful 15hp air compressor manufacturer in the industry, Premium quality products, Best warranty and highest customer satisfaction! We know that there is only one way to reach our goals, by doing things right! We use only the best Brand name components to manufacture our products. Our 15hp air compressor Rotary screws have the newest and greatest technology in the compressor industry. The Polar Air by Eaton Compressor 3rd Generation rotary screw units have top shelf brand name components with NO china parts! These Top brand suppliers have been in business for many years and provide only the best quality and energy efficiency, parts/service will give the best all around support for our customers.Our, best in the compressor industry warranty reflects our units quality with no tricks or deception. We offer NO generic parts. These top brand parts suppliers come at a higher cost to our company 30% more then the cheaper generic brands. We would rather use the best brand parts and pay a little more upfront, then have a dissatisfied customer down the road with parts availability and quality. Our shopping customers ask how do you compare against brand X....? we think we are better in a lot of ways. Our screw pumps, electric motors, magnetic contactors and filters are none proprietary to our brand. This gives the customer a fair option. Proprietary parts is another way to rip off the customer. We have seen PLC's cost $3,000 on a $5,000 compressor. This same comparable PLC through our company is $750. We have seen motors from other big brands made proprietary to their design purposely costing 500% more than our motor. We have seen magnetic contactor's from our competitors with special part numbers costing 500% more. We have seen the screw compressor pumps from the competitor that are proprietary to their design costing 500% more. Save yourself from being ripped off when quoting your next compressor, be sure to get a quote from them on the compressor and main replacement parts and compare. Ask the replacement cost for the screw, electric motor, filters, cooling radiator and fan. We encourage you to compare so Let us share with you why we are the best!
The Airend is the most important part of your compressor, it is the heart of the machine that actually compresses the air. That is why here at, Polar Compressor by Eaton Compressor we use only the best German and Finland name brand airends. The German made EVO Rotocomp have been producing these airends for over 65 years. Our Finland made G.D airends have been around since the early 1900'S. Most airends are only good for up to 40,000 hours and then they need a complete overhaul, with our airends they are good for 70,000 running hours as long as the unit is maintenance routinely and the correct oil is used. Polar Air Gives you a 10 year warranty on all their airends!
All Polar Air Rotary Screw air compressors are equipped with these state of the art screw airend compressors manufactured in Germany and Finland. These airends have precision-aligned back to back tapped roller bearings with close tolerances guarantee long life cycles and out standing reliability. Each air end is tested to meet consistent high quality standards.
These State of the art airends air cooled by a flood of injected oil. The oil injection sprays directly onto the rotors and roller bearings,
this helps efficiently cool the compressor. The oil helps to seal any gaps or clearances between the rotors and the housing. It works
in the way of not allowing air to flow back the wrong way thus lowering your air ends efficiency and performance
These units comes mounted on a 120 gallon Horizontal painted receiving tank equipped with auto drain , hydraulic hoses and fittings.
These tanks are made in the USA and have ring based design to prevent cracking, Standard NPT ports, ASME, NBBI, & CRN approvals, they are rated up to 450 degrees F, and they are coated with anti corrosive/ rust prevention blended steel to increase the tanks life.
We use only premium industrial name brand motors to run our compressors. Polar air uses only low 1750 RPM motors. We have chosen motors that come with the best certificates and quality assurances so we know that you are getting the best as well! We use High Efficiency inventer variable speed duty motors constructed with superior materials, higher service factors, longer bearing lives, lower waste- heat output and less vibration. We also pass the motor warranty on to you for a full 5 year on single phase and a full 10 year on 3 phase!!
The Hyundai motors are made of heavy duty cast iron construction. Hyundai motor Company has been around since 1967. We use TEFC (Total enclosed fan cooled ) , meaning the motor is dust tight and doesn't allow outside air in, it instead uses the fan to blow air over the frame of the motor to cool it. These motors all have copper bar rotors, this technology dates back to the 1920's. Copper helps improve the electrical energy efficiency of the motor because of its density and ability to transfer energy. Many motors are made of aluminum rotors, these inefficient electric motors waste electrical energy and therefore cost more to operate. Copper reduces the energy loss by 15-20% compared to aluminum. Inefficient motors case many issues, they waste more energy, in turn increasing electrical demand,, thus increasing your electrical cost. Copper generates less heat and thermal stress therefore enabling longer life to the motor then aluminum.
As mention earlier the airend is the heart of the compressor but is does not work alone. The outside air is brought in and filtered before it hits the inlet valve to insure it is receiving clean air. The inlet valve regulates the amount of air that is sucked in by the rotary screw. When the valve is in a "loaded state it is compressing air and pumping it into the airend, when it is in an "unloaded" state is shuts off the air supply, so the motor and screw air turning but not taking in air. Therefore not pumping any air to the system. Our VMC inlet valves have a counter weight which insures fast, tight closer when the air flow is reversed. This load and unload system has greater energy savings as well. When running the compressor in unloaded state it allows the compressor to store more air then is being used., a storage tank must be used in this case. The larger the the storage tank the longer the the no load cycle time, the greater the savings. This unis will save you hundreds on your electric bill because under start up the modulator valve is completely closed. This closes the air off to the screw intake making low load under start up. After the unit gets started, it has a 12-secound time delay. this allows the unit to get running fro 12 seconds before it starts pumping air. This makes no load starting and will save your magnetic starter contractor and motor because of low amp draw. VMC was established in the 1970's.
15hp air compressor by Eaton Compressor is controlled by a user friendly Logika PLC (Programmable Logistic Controller). This controller makes this unit bullet proof. These controllers have may many features that are extremely user friendly and easy to use. Here are some of its key features.
•variable speed ready to Control the speed of the motor•Adjust Pressure - to what pressure range you need. This can be set by the customer, this unit has a shutdown in case the unit goes over pressure. the unit has a maximum pressure setting - the computer will sense that it is going over pressure and will shut down. •Low Oil Shutdown - if the controller senses that the unit is going into high temperature it will shut it down. It will also shut down if the compressor runs low on oil. •Reverse Fault - the controller will control when the unit is wired up if it is running backwards, it will sense a reverse rotation fault and shut the unit down•High Voltage Fault - if the voltage is 15% over the power supply voltage rated on the Polar compressor data plate, the unit will shut down. Also if the voltage is 15% under it will shut is down as well.•Over AMP Shut down - if the motor is pulling to many amps it will shut down. You can check the amp draw of the electric motor as it is running and also on the exhaust fan motor•Clock and Date - Built in Clock and Date to help keep track of preventative maintenance services.
Filters help protect the compressor from wear and damage. It is the most inexpensive way to prevent possible costly repairs. It is vital that these filters are replaced and inspected on a routine basis, the timing is important as is reduces the chances of component and airend contamination. It can decrease the energy efficiency of your machine as well if not done. Because we know the importance we use only genuine Mann Filters. These Filters are not exclusive to us therefore after your warranty is up you will still be able to find these parts. Mann Filters are made with exceptional quality and provide optimum protection against harmful elements. Our rotary's also have Pre-Filtration on the outside of the cabinets. Although this is an upgraded feature it is one that is well worth the cost to protect the life of your compressor. Even in environments that are not that dirty the build up over time can be damaging to the system and seriously impact the performance. ask about adding a Pre-filter kit to your system to save even more money!
When it comes to the smaller parts of our units we don't spare on quality neither. For Our electrical components are French made Telemecanique, they are also UL/CSA compliant. We use High quality brass valves. We use V-Belts from top name brands that are rated for 25,000 hour life expectancy. The Rotary screw cabinet is made with heavy metal construction with easy latch doors that contain sound proof material for ultra quiet operation. We do not use china parts on any of our rotary screws! We know that our units will prove themselves worthy of being the best air compressors on the market! Once you purchase one of our compressor from any of our series you are part of the Polar Compressor Family! If you have any questions or air ready for a quote please contact someone form our sales team and they will be happy to help!
Polar Air by Eaton Compressor backs all their compressors with the best warranty in the industry, and we are not kidding we did the homework! WE have provided you with the warranty comparison as well. Polar Air By Eaton Compressor gives their Rotary screws a full 10 year warranty! The warranty is NOT pro-rated. Make sure to research and ask questions when warranty comparing. Be sure when you buy that you are buying a FULL warranty. Just remember, a Pro-rated warranty means that the older the compressor gets the more risk you are in, the potential percentage is higher that you may pay out of your pocket. With our warranty we don't ask you to buy a service plan or extended warranty, we just ask that you purchase and use our oil and filters. This ensures the correct oil with the specs needed to run our pumps is used. Our trained service and support team is ready if you ever need them and we carry a full line of new replacement parts.
|Product Source||America, Germany, Italy - NO-CHINA|
|CFM||70 @ 100 PSI|
|Compressor Style||Rotary - Swingarm Complete Package|
|Air End Model||Rotocomp -EVO03|
|Dimension: Length x Depth x Height (in inches)||71 x 27 x 70 - Complete Package|
|Motor Type||Hyundai TEFC|
|Voltage||208/230/380/460/575 - options|
|Tank Size||120 Gallon|
|Air Dryer Information|
|Dryer CFM||115 CFM|
|Dryer DIMS||26" x 23" x 36|
|Dryer Outlet Size||1 1/2"|
|Dryer Orientation||Swingarm Hinge-Easy Access|
|Dryer Drain||Built in Automatic|
|Dryer filtration||Built in Coalescing Filter|
|Dew Point (degrees F)||37-50|
|Max Ambient Temperature (degrees F)||122|
|Max Rated Inlet Temperature (degrees F)||140|